Catalog #22416 (4/03)MicroTUV ONLINE UVTRANSMISSION SENSOR/SAMPLEROPERATION & MAINTENANCE MANUALHF scientific, inc.3170 Metro ParkwayFort Myers, F
2.0 INSTALLATION2.1 PACKING LIST FOR THE TUVCONTENTS QUANTITY1) Sensor/Sampler enclosure 12) Cold Weather Kit 1 Heating Cable 25 ft. 8” Couple
2.3.2 Installing the Desiccant Tray and PouchBefore operating the Micro TUV for the first time the desiccant tray andfoot valve assembly must be insta
TUV (04/03) Page 4REV. 0.62.4.2 Pipe Insulation InstallationPull the intake and drain lines out and lay them together with the heating cable (which
Inside the Sensor module, warm dry air is constantly circulated around the exterior of the sampling cuvetteto prohibit condensation. A desiccant tra
TUV (04/03) Page 6REV. 0.65.0 FLOW SENSORThe Sensor/Sampler has a flow sensor that will detect a flow failure, turn off the pump and indicate a
6.1 SYSTEM CLEANINGCAUTION: Avoid getting air into the system. Avoid letting the source line come out of thesource water.CAUTION: If the system is
If the cuvette does not appear to be clean, use soft, lint-free tissues (i.e. Kimwipe® ) to wipe the inside then rinsewith clean water. Dry the outsi
A full bottle of 100% T solution will last for about 15 calibrations. The controller or analyzer will remind youwhen the bottle is empty. Replaceme
6.8 REPLACING SYSTEM TUBINGAll the tubing in the system should be checked at least yearly for wear. A Tubing Kit (Part# 22887) is avail-able which co
TUV (04/03) Page 11REV. 0.6 7.2 TROUBLESHOOTING GUIDEThe following table will supply fundamental troubleshooting information. The guide assumes tha
7.3 REPLACEMENT PARTSPart No. Description19306 100% T Solution, 1 x 4 gallon/4L20616 Heating Cable (120V)20815 Wire Shielded RS-485 (per foot)19403 C
Figure 3Sensor/Sampler Outline DimensionsTUV(04/03) Page 13REV. 0.6
Figure 4Interior/Exterior Plumbing and Electrical ConnectionsTUV(04/03) Page 14REV. 0.6
TUV (04/03) Page 15REV. 0.6Figure 5Power Input Cable Connections
Figure 6Heater Cable Stripping InstructionsTUV (04/03) Page 16REV. 0.6
Figure 7Cold Weather Kit Installation DetailsTUV (04/03) Page 17REV. 0.6
WARRANTY HF scientific, inc., as manufacturer, warrants to the original purchaser of the instruments to befree of defects in material and workmans
DATE: August 11, 1998REVISION: 3MATERIAL SAFETY DATA SHEETHF scientific, inc.3170 Metro ParkwayFort Myers, FL 33916-7597239-337-2116EMERGENCY CONTACT:
TABLE OF CONTENTS Page No.1.0 IMPORTANT INFORMATION ... 11.1 HOW TO USE THIS MANUAL ...
TABLE OF CONTENTS (Continued...)FiguresFigure No. Title Page No.1 Desiccant Tray Installation ...
DECLARATION OF CONFORMITYApplication of Council Directive: 89/336/EECStandards to which Conformity is Declared:Product Safety Immunity EMIUL3101-1 EN
1.0 IMPORTANT INFORMATION1.1 HOW TO USE THIS MANUALThis equipment, while sophisticated, has been designed for simple and easy operation. Inkeepin
Commentaires sur ces manuels