Hf-scientific Oil Content Bilge Alarm Manuel d'utilisateur

OPERAOPERAOPERAOPERAOPERATING & MAINTENTING & MAINTENTING & MAINTENTING & MAINTENTING & MAINTENANCEANCEANCEANCEANCEMANUMANUMANUMAN

Bilge Alarm (02/02)Rev. 1.3XVI. TROUBLE-SHOOTING GUIDESYMPTOMS PROBABLE CAUSE CORRECTIVE ACTIONDigital Display and/or indicatinglights do not light u

Bilge Alarm (02/02)Rev. 1.3 XVII. TEST PROCEDURES FOR POWER SUPPLY BOARD (LOWER PC BOARD IN Figure 3)1. Turn Power OFF.2. Remove Amplifier P.C. Board

Bilge Alarm (02/02)Rev. 1.3C21+ 12R332 4 5 6C6C7 +879 10 11REC ALMU3U1C4U4R413 14 1580103U2 +C5U5R6C1RECORDSW1U6C3R10R2R1R9

Bilge Alarm (02/02)Rev. 1.3RelayCatalog No. 80134Qty. 1Photo Diode AssemblyCatalog No. 81010Qty. 1In-Line Calibrator Kit & Cleaning BrushCatalog

Bilge Alarm (02/02)Rev. 1.3XIX. WARRANTYHF scientific, inc., as vendor, warrants to the original purchaser of the instruments to be free of defects i

Bilge Alarm (02/02)Rev. 1.3System Installation DiagramFigure 1Page 11

Bilge Alarm (02/02)Rev. 1.3Sensor Installation DiagramFigure 2Page 12

Bilge Alarm (02/02)Rev. 1.3USENSORREMOTEJ2-1J2-9 YELLOWORANGEBLACKREDGREENWHITEWHT/REDBLK/REDWHTBLKBLKBLKWHTWHT WHTBLKWHTBLKWHTGRNV/BLKV/BLKGRN/WH

Figure 4Interconnecting Wiring1718192021222324TB3LINE115/220VACGREENWHITEBLACKTB16780-10VOUTPUTTB2910 11 12 13 1415 16(1) RELAY CONTACTS AT TB3 17 &a

Figure 5Location of PartsPage 15Bilge Alarm (02/02)Rev. 1.3(A) Amplifier P.C. Board(B)(D)(G)(F)(E)(H)CALCHECK ALARMSETREC D.V.MALARM(C) Power Supp

At Sea SparAt Sea SparAt Sea SparAt Sea SparAt Sea Spare Pe Pe Pe Pe Parararararts Kitts Kitts Kitts Kitts Kitfffffor the HF scientifor the HF scienti

Bilge Alarm (02/02)Rev. 1.3

Bilge Alarm (02/02)Rev. 1.3Figure 6Location of Parts(A)E9(C)(B)RECD.V.M.ALMCALCHKALMSETCOM-15\V+15V-5V+5V+2.5V+24VPage 16

Bilge Alarm (02/02)Rev. 1.3

Bilge Alarm (02/02)Rev. 1.3SHLDLAMPVoVcc123456789Sensor ConnectionsFigure 7Page 17

Bilge Alarm (02/02)Rev. 1.3Control Module OutlineFigure 81-3/834.95-1/4133.46-1/4158.71-3/834.91.025.411-1/8282.610-3/4273.13/89.5.2817.1410-HOLESDIA

Bilge Alarm (02/02)Rev. 1.3114.3155.650.895.388.992.182.5127DIA.DIA.DIMENSIONS=INCHESMMCLLCLCCLCL1 NPT2-PLACES1/2 NPT3 3/42.06 1/83 1/23 5/84 1/23 1/

Bilge Alarm (02/02)Rev. 1.3Figure 10Digital Display Schematic DrawingREF HI+5V POL(MINUS)AB4 A3 B3 C3 D3 E3 F3 G3 A2 B2 C2 D2 E2 F2 G2

Bilge Alarm (02/02)Rev. 1.3Figure 11Power Supply SchematicPage 21

Bilge Alarm (02/02)Rev. 1.3Figure 12Amplifier Board Schematic2N5785ALARMD.V.M.+15V1.21M10mfd+C855517LMU626438.01mfdC915KR10308+-3.3mfdC73.3mfdC6+15V-

IMPORTANTIMPORTANTIMPORTANTIMPORTANTIMPORTANTCalibration / Cleaning KitCalibration / Cleaning KitCalibration / Cleaning KitCalibration / Cleaning KitC

CONTENTSCONTENTSCONTENTSCONTENTSCONTENTSPAGEI. SPECIFICATIONS ...

Bilge Alarm (02/02)Rev. 1.3I. SPECIFICATIONSRange 0 - 100 PPMOutputs Recorder Output: 0-10 V.D.C., minimum impedance 500 ohms.Digital display: 2 1/

Bilge Alarm (02/02)Rev. 1.3II. WARNINGThe Sensing Module and the Indicating/Control Moduleare shipped with the Interconnecting Cable connectedfor rea

Bilge Alarm (02/02)Rev. 1.3of 5 amps at 120VAC or 28 VDC resistive.There are two sets of contacts which may be used tooperate valves, sound alarms, e

Bilge Alarm (02/02)Rev. 1.3IX. ISOLATION VALVESIsolation valves should be operated to shut-off flow fromthe Oily-Water Filter under each of the foll

Bilge Alarm (02/02)Rev. 1.3XIV. REPLACING SENSING MODULEMEASUREMENT DETECTOR (Refer to Figure 7)1. Turn OFF the Power Switch at the Indicating/Contro